Leader in Differential GNSS Solutions Worldwide

Trimble

Agriculture Receivers

Trimble Agriculture receivers that support OmniSTAR services include the following:

  • AgGPS AutoPilot
  • FmX Integrated Display
  • CFX-750 Display
  • EZ-Guide 500
  • AgGPS 542
  • AgGPS 332
  • AgGPS 252
  • AgGPS 132
  • AgGPS 114

Technical information for many of these receivers can be found below. For additional information, please refer to Trimble’s website at www.trimble.com/agriculture/.

Mapping / GIS Receivers

Technical information is available here for the following Trimble Pathfinder receivers:

  • Trimble Pathfinder ProXRS
  • Trimble Pathfinder Power
  • Trimble Pathfinder ProXRT

For information about other Trimble Mapping & GIS receivers, please visit the Trimble website at www.trimble.com/mappingGIS.

Construction Receivers

Trimble Construction receivers that support OmniSTAR services include the following:

  • SPS-850 series
  • SPS-750 series
  • SPS-550 series
  • DSM 132
  • DSM 232

Technical information for many of these receivers can be found by selecting More below. For additional information, please refer to Trimble’s website.

 AgGPS 114

Use the AgRemote program (available here) to set up your Ag114 receiver for your OmniSTAR activation.

  1. Use AgRemote, after connecting to the receiver the rest of the procedure is the same as the Trimble Ag132 above.
  2. From the HOME SCREEN press the RIGHT ARROW key until you access the CONFIGURATION screen.
  3. Press DOWN ARROW key to enter these screens
  4. Press RIGHT ARROW key until you access the DGPS CONFIGURATION screen.
  5. Press DOWN ARROW key until DGPS SOURCE screen appears.
  6. Choose SATELLITE ONLY
  7. Press ENTER key
  8. Press DOWN ARROW key until EZ SAT: screen appears.
  9. Use arrow keys to set provider to OMNI
  10. Press ENTER key
  11. Use arrow keys to choose the correct satellite for your area. For a list of satellite frequencies, click here.
  12. Press ENTER key
  13. Press DOWN ARROW key until SATELLITE FREQ screen appears.
  14. This will list the frequency of the DGPS satellite you specified in the EZ SAT: field. Press DOWN ARROW key until SATELLITE BAUD RATE screen appears.
  15. This should update to the Data Rate of the satellite you specified in the EZ SAT: field. Press DOWN ARROW key until prompted to exit DGPS CONFIG. screen.
  16. Press ENTER key to exit.
  17. After changing the frequency, restore the settings of Port A to Port output NMEA baudrate 9600,8,N,1.
  18. The program will reply an error message: “Lost communications with the receiver check cables”
  19. Allow 30-45 minutes to get the system to work during the activation process

OmniSTAR must then send an activation code (RSOC-type) over the satellite to the unit. When received, it will display RESET BY OMNI ACTIVATION, PLEASE HIT ENTER TO CONTINUE. It can take up to 30 minutes for activation to be complete. It is important that the system be left on until the receiver positions differentially.

To check that activation was successful:

  1. Connect to AgRemote
  2. From the HOME SCREEN press the RIGHT ARROW key until you access the STATUS screen.
  3. Press DOWN ARROW key to enter these screens
  4. Use RIGHT ARROW key, access the DGPS SCREEN
  5. Press DOWN ARROW key.
  6. First screen should display Satellite Frequency and S/N of the satellite signal-noise ratio and the strength of the differential satellite lock.
  7. Press DOWN ARROW key and screen should display Omni as SERVICE PROVIDER.
  8. Press DOWN ARROW key and DGPS DATA SOURCE should read correct REFERENCE STATION ID.
  9. Press DOWN ARROW key and screen should display AGE of DGPS and AGE of SYNC.
  10. Press DOWN ARROW key until Omni*SERVICE INFO appears
  11. Press ENTER key to access this screen.
  12. Use ENTER key to scroll through the screens for status of the OmniStar subscription activation noting USER ENABLED and STOP DATE.
  13. Use ARROW keys to display HOME SCREEN.
  14. The HOME SCREEN will display on the top line, the type of position recorded. THE letter G will be replaced as a D when the receiver starts computing differentially corrected positions. The second line should display the DGPS satellite frequency.
  15. After changing the frequency, restore the settings of Port A to Port output NMEA baudrate 9600,8,N,1.
  16. The program will reply an error message: “Lost communications with the receiver check cables”

To change to a satellite frequency that already exists in the EZ SAT list, follow the instructions above for Activation Set-up.

To change to a new satellite frequency that may not be in the EZ SAT list, follow the instructions below:

  1. Use the AgRemote program (available here) to change the OmniSTAR satellite frequency.
  2. Use AgRemote, after connecting to the receiver the rest of the procedure is the same as the Trimble Ag132 above.
  3. From the HOME SCREEN press the RIGHT ARROW key until you access the CONFIGURATION screen.
  4. Press DOWN ARROW key to enter these screens
  5. Press RIGHT ARROW key until you access the DGPS CONFIGURATION screen.
  6. Press DOWN ARROW key until DGPS SOURCE screen appears.
  7. Press RIGHT ARROW key
  8. Press DOWN ARROW key until it says SATELLITE ONLY
  9. Press ENTER key
  10. Press DOWN ARROW key until SATELLITE FREQ screen appears.
  11. Press RIGHT ARROW key
  12. Use UP ARROW and DOWN ARROW keys to change the digits to the correct frequency for your area. Use the RIGHT ARROW key to move the cursor. For a list of satellite frequencies, click here.
  13. Press ENTER key
  14. Press DOWN ARROW key until SATELLITE BAUD screen appears.
  15. Press RIGHT ARROW key
  16. Use UP ARROW and DOWN ARROW keys to select the correct baud rate for your area. For a list of satellite frequencies and baud rates, click here.
  17. Press ENTER key to exit.
  18. After changing the frequency, restore the settings of Port A to Port output NMEA baudrate 9600,8,N,1.
  19. The program will reply an error message: “Lost communications with the receiver check cables”

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

 
Trimble AgGPS 114

  RSOCVBS n/a  3.00
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
Trimble AgGPS 114
 3.06 3.00  n/a Oct. 2005
VBS

Documentation available for the Trimble AgGPS 114 includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 AgGPS 132

  1. From the HOME SCREEN press the RIGHT ARROW key until you access the CONFIGURATION screen.
  2. Press DOWN ARROW key to enter these screens
  3. Press RIGHT ARROW key until you access the DGPS CONFIGURATION screen.
  4. Press DOWN ARROW key until DGPS SOURCE screen appears.
  5. Choose SATELLITE ONLY
  6. Press ENTER key
  7. Press DOWN ARROW key until EZ SAT: screen appears.
  8. Use arrow keys to set provider to OMNI
  9. Press ENTER key
  10. Use arrow keys to choose the correct satellite for your area. For a list of satellite frequencies, click here.
  11. Press ENTER key
  12. Press DOWN ARROW key until SATELLITE FREQ screen appears.
  13. This will list the frequency of the DGPS satellite you specified in the EZ SAT: field. Press DOWN ARROW key until SATELLITE BAUD RATE screen appears.
  14. This should update to the Data Rate of the satellite you specified in the EZ SAT: field. Press DOWN ARROW key until prompted to exit DGPS CONFIG. screen.
  15. Press ENTER key to exit.
  16. Allow 30-45 minutes to get the system to work during the activation process. OmniSTAR must then send an activation code (RSOC-type) over the satellite to the unit. When received, it will display RESET BY OMNI ACTIVATION, PLEASE HIT ENTER TO CONTINUE. It can take up to 30 minutes for activation to be complete. It is important that the system be left on until the receiver positions differentially.

To check that activation was successful:

  1. From the HOME SCREEN press the RIGHT ARROW key until you access the STATUS screen.
  2. Press DOWN ARROW key to enter these screens
  3. Use RIGHT ARROW key, access the DGPS SCREEN
  4. Press DOWN ARROW key.
  5. First screen should display Satellite Frequency and S/N of the satellite signal-noise ratio and the strength of the differential satellite lock.
  6. Press DOWN ARROW key and screen should display Omni as SERVICE PROVIDER.
  7. Press DOWN ARROW key and DGPS DATA SOURCE should read correct REFERENCE STATION ID.
  8. Press DOWN ARROW key and screen should display AGE of DGPS and AGE of SYNC.
  9. Press DOWN ARROW key until Omni*SERVICE INFO appears
  10. Press ENTER key to access this screen.
  11. Use ENTER key to scroll through the screens for status of the OmniStar subscription activation noting USER ENABLED and STOP DATE.
  12. Use ARROW keys to display HOME SCREEN.
  13. The HOME SCREEN will display on the top line, the type of position recorded. THE letter G will be replaced as a D when the receiver starts computing differentially corrected positions. The second line should display the DGPS satellite frequency.

To change to a satellite frequency that already exists in the EZ SAT list, follow the instructions above for Activation Set-up.

To change to a new satellite frequency that may not be in the EZ SAT list, follow the instructions below:

  1. From the HOME SCREEN press the RIGHT ARROW key until you access the CONFIGURATION screen.
  2. Press DOWN ARROW key to enter these screens
  3. Press RIGHT ARROW key until you access the DGPS CONFIGURATION screen.
  4. Press DOWN ARROW key until DGPS SOURCE screen appears.
  5. Press RIGHT ARROW key
  6. Press DOWN ARROW key until it says SATELLITE ONLY
  7. Press ENTER key
  8. Press DOWN ARROW key until SATELLITE FREQ screen appears.
  9. Press RIGHT ARROW key
  10. Use UP ARROW and DOWN ARROW keys to change the digits to the correct frequency for your area. Use the RIGHT ARROW key to move the cursor. For a list of satellite frequencies, click here.
  11. Press ENTER key
  12. Press DOWN ARROW key until SATELLITE BAUD screen appears.
  13. Press RIGHT ARROW key
  14. Use UP ARROW and DOWN ARROW keys to select the correct baud rate for your area. For a list of satellite frequencies and baud rates, click here.
  15. Press ENTER key to exit.
  16. Allow 30-45 minutes to get the system to work

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model      VBS Subscription     HP/XP Subscription      Firmware Version 

Trimble AgGPS 132Also:OmniLite 132OmniSTAR 3200

  RSOCVBS n/a  3.00 or 1.52 special
   GPS Receiver Model     Latest  Firmware   VBS2 Compatible  XP  Compatible     Release date    VBS/HP/G2 
Trimble AgGPS 132Also:Trimble DSM132P/N 33302-x0  1.55  1.54  n/a  June 2007 VBS

Documentation available for the Trimble AgGPS 132 includes the following:

  • User manual
  • OmniSTAR technical note: Changing frequencies using AgRemote

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 AgGPS 252

Use the AgRemote program (available here) to set up your Ag252 receiver for your OmniSTAR activation.

  1. Use AgRemote, after connecting to the receiver the rest of the procedure is the same as the Trimble Ag132 above.
  2. From the HOME SCREEN press the RIGHT ARROW key until you access the CONFIGURATION screen.
  3. Press DOWN ARROW key to enter these screens
  4. Press RIGHT ARROW key until you access the DGPS CONFIGURATION screen.
  5. Press DOWN ARROW key until DGPS SOURCE screen appears.
  6. Choose SATELLITE ONLY
  7. Press ENTER key
  8. Press DOWN ARROW key until EZ SAT: screen appears.
  9. Use arrow keys to set provider to OMNI
  10. Press ENTER key
  11. Use arrow keys to choose the correct satellite for your area. For a list of satellite frequencies, click here.
  12. Press ENTER key
  13. Press DOWN ARROW key until SATELLITE FREQ screen appears.
  14. This will list the frequency of the DGPS satellite you specified in the EZ SAT: field. Press DOWN ARROW key until SATELLITE BAUD RATE screen appears.
  15. This should update to the Data Rate of the satellite you specified in the EZ SAT: field. Press DOWN ARROW key until prompted to exit DGPS CONFIG. screen.
  16. Press ENTER key to exit.
  17. After changing the frequency, restore the settings of Port A to Port output NMEA baudrate 9600,8,N,1.
  18. The program will reply an error message: “Lost communications with the receiver check cables”
  19. Allow 30-45 minutes to get the system to work during the activation process

OmniSTAR must then send an activation code (RSOC-type) over the satellite to the unit. When received, it will display RESET BY OMNI ACTIVATION, PLEASE HIT ENTER TO CONTINUE. It can take up to 30 minutes for activation to be complete. It is important that the system be left on until the receiver positions differentially.

To check that activation was successful:

  1. Connect to AgRemote
  2. From the HOME SCREEN press the RIGHT ARROW key until you access the STATUS screen.
  3. Press DOWN ARROW key to enter these screens
  4. Use RIGHT ARROW key, access the DGPS SCREEN
  5. Press DOWN ARROW key.
  6. First screen should display Satellite Frequency and S/N of the satellite signal-noise ratio and the strength of the differential satellite lock.
  7. Press DOWN ARROW key and screen should display Omni as SERVICE PROVIDER.
  8. Press DOWN ARROW key and DGPS DATA SOURCE should read correct REFERENCE STATION ID.
  9. Press DOWN ARROW key and screen should display AGE of DGPS and AGE of SYNC.
  10. Press DOWN ARROW key until Omni*SERVICE INFO appears
  11. Press ENTER key to access this screen.
  12. Use ENTER key to scroll through the screens for status of the OmniStar subscription activation noting USER ENABLED and STOP DATE.
  13. Use ARROW keys to display HOME SCREEN.
  14. The HOME SCREEN will display on the top line, the type of position recorded. THE letter G will be replaced as a D when the receiver starts computing differentially corrected positions. The second line should display the DGPS satellite frequency.
  15. After changing the frequency, restore the settings of Port A to Port output NMEA baudrate 9600,8,N,1.
  16. The program will reply an error message: “Lost communications with the receiver check cables”

To change to a satellite frequency that already exists in the EZ SAT list, follow the instructions above for Activation Set-up.

To change to a new satellite frequency that may not be in the EZ SAT list, follow the instructions below:

  1. Use the AgRemote program (available here) to change the OmniSTAR satellite frequency. A more detailed version of this procedure can be found here << add link>>.
  2. Use AgRemote, after connecting to the receiver the rest of the procedure is the same as the Trimble Ag132 above.
  3. From the HOME SCREEN press the RIGHT ARROW key until you access the CONFIGURATION screen.
  4. Press DOWN ARROW key to enter these screens
  5. Press RIGHT ARROW key until you access the DGPS CONFIGURATION screen.
  6. Press DOWN ARROW key until DGPS SOURCE screen appears.
  7. Press RIGHT ARROW key
  8. Press DOWN ARROW key until it says SATELLITE ONLY
  9. Press ENTER key
  10. Press DOWN ARROW key until SATELLITE FREQ screen appears.
  11. Press RIGHT ARROW key
  12. Use UP ARROW and DOWN ARROW keys to change the digits to the correct frequency for your area. Use the RIGHT ARROW key to move the cursor. For a list of satellite frequencies, click here.
  13. Press ENTER key
  14. Press DOWN ARROW key until SATELLITE BAUD screen appears.
  15. Press RIGHT ARROW key
  16. Use UP ARROW and DOWN ARROW keys to select the correct baud rate for your area. For a list of satellite frequencies and baud rates, click here.
  17. Press ENTER key to exit.
  18. After changing the frequency, restore the settings of Port A to Port output NMEA baudrate 9600,8,N,1.
  19. The program will reply an error message: “Lost communications with the receiver check cables”

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

Trimble AgGPS 252

RSOCVBS RSOCHP 3.1 / 3.5
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
Trimble AgGPS 252
 3.70 3.1  3.1 Jan. 2006
VBS/HP

Documentation available for the Trimble AgGPS 252 includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 AgGPS 262

For activation set-up, please refer to the manufacturer’s website at http://www.trimble.com/agriculture.

To change to a new satellite frequency, please refer to the manufacturer’s website at http://www.trimble.com/agriculture.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

Trimble AgGPS 262

  RSOCVBS RSOCHP  <<TBA>>
   GPS Receiver Model   
Latest   Firmware
 VBS2
 Compatible 
XP
 Compatible 
Release date 
  VBS/HP/G2 
Trimble AgGPS 262 5.10 All All  June 2007
VBS/HP

Documentation available for the Trimble AgGPS 262 includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com/agriculture.

 AgGPS 332

  1. From the HOME SCREEN press the RIGHT ARROW key until you access the CONFIGURATION screen.
  2. Press DOWN ARROW key to enter these screens
  3. Press RIGHT ARROW key until you access the DGPS CONFIGURATION screen.
  4. Press DOWN ARROW key until DGPS SOURCE screen appears.
  5. Choose SATELLITE ONLY
  6. Press ENTER key
  7. Press DOWN ARROW key until EZ SAT: screen appears.
  8. Use arrow keys to set provider to OMNI
  9. Press ENTER key
  10. Use arrow keys to choose the correct satellite for your area. For a list of satellite frequencies, click here.
  11. Press ENTER key
  12. Press DOWN ARROW key until SATELLITE FREQ screen appears.
  13. This will list the frequency of the DGPS satellite you specified in the EZ SAT: field. Press DOWN ARROW key until SATELLITE BAUD RATE screen appears.
  14. This should update to the Data Rate of the satellite you specified in the EZ SAT: field. Press DOWN ARROW key until prompted to exit DGPS CONFIG. screen.
  15. Press ENTER key to exit.
  16. Allow 30-45 minutes to get the system to work during the activation process

OmniSTAR must then send an activation code (RSOC-type) over the satellite to the unit. When received, it will display RESET BY OMNI ACTIVATION, PLEASE HIT ENTER TO CONTINUE. It can take up to 30 minutes for activation to be complete. It is important that the system be left on until the receiver positions differentially.

To check that activation was successful:

  1. From the HOME SCREEN press the RIGHT ARROW key until you access the STATUS screen.
  2. Press DOWN ARROW key to enter these screens
  3. Use RIGHT ARROW key, access the DGPS SCREEN
  4. Press DOWN ARROW key.
  5. First screen should display Satellite Frequency and S/N of the satellite signal-noise ratio and the strength of the differential satellite lock.
  6. Press DOWN ARROW key and screen should display Omni as SERVICE PROVIDER.
  7. Press DOWN ARROW key and DGPS DATA SOURCE should read correct REFERENCE STATION ID.
  8. Press DOWN ARROW key and screen should display AGE of DGPS and AGE of SYNC.
  9. Press DOWN ARROW key until Omni*SERVICE INFO appears
  10. Press ENTER key to access this screen.
  11. Use ENTER key to scroll through the screens for status of the OmniStar subscription activation noting USER ENABLED and STOP DATE.
  12. Use ARROW keys to display HOME SCREEN.
  13. The HOME SCREEN will display on the top line, the type of position recorded. THE letter G will be replaced as a D when the receiver starts computing differentially corrected positions. The second line should display the DGPS satellite frequency.

To change to a satellite frequency that already exists in the EZ SAT list, follow the instructions above for Activation Set-up.

To change to a new satellite frequency that may not be in the EZ SAT list, follow the instructions below:

  1. From the HOME SCREEN press the RIGHT ARROW key until you access the CONFIGURATION screen.
  2. Press DOWN ARROW key to enter these screens
  3. Press RIGHT ARROW key until you access the DGPS CONFIGURATION screen.
  4. Press DOWN ARROW key until DGPS SOURCE screen appears.
  5. Press RIGHT ARROW key
  6. Press DOWN ARROW key until it says SATELLITE ONLY
  7. Press ENTER key
  8. Press DOWN ARROW key until SATELLITE FREQ screen appears.
  9. Press RIGHT ARROW key
  10. Use UP ARROW and DOWN ARROW keys to change the digits to the correct frequency for your area. Use the RIGHT ARROW key to move the cursor. For a list of satellite frequencies, click here.
  11. Press ENTER key
  12. Press DOWN ARROW key until SATELLITE BAUD screen appears.
  13. Press RIGHT ARROW key
  14. Use UP ARROW and DOWN ARROW keys to select the correct baud rate for your area. For a list of satellite frequencies and baud rates, click here.
  15. Press ENTER key to exit.
  16. Allow 30-45 minutes to get the system to work

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

Trimble AgGPS 332
Also:
Trimble DSM232

  RSOCVBS RSOCHP  3.1 / 3.5
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
Trimble AgGPS 332
Also:
Trimble DSM232

 3.70  3.1 3.1  Jan. 2006
VBS/HP

Documentation available for the Trimble AgGPS 332 includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 CFX-750 Display

For activation set-up, please refer to the manufacturer’s website at http://www.trimble.com/agriculture.

To change to a new satellite frequency, please refer to the manufacturer’s website at http://www.trimble.com/agriculture.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model      VBS Subscription     HP/XP Subscription      Firmware Version 

Trimble CFX-750 Display

  RSOCVBS RSOCHP TBA
   GPS Receiver Model    Latest   Firmware  VBS2 Compatible  XP Compatible  Release date    VBS/HP/G2 

Trimble CFX-750 Display

TBA All All TBA VBS/HP/G2

Documentation available for the Trimble CFX-750 Display includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 DSM 132

  1. From the HOME SCREEN press the RIGHT ARROW key until you access the CONFIGURATION screen.
  2. Press DOWN ARROW key to enter these screens
  3. Press RIGHT ARROW key until you access the DGPS CONFIGURATION screen.
  4. Press DOWN ARROW key until DGPS SOURCE screen appears.
  5. Choose SATELLITE ONLY
  6. Press ENTER key
  7. Press DOWN ARROW key until EZ SAT: screen appears.
  8. Use arrow keys to set provider to OMNI
  9. Press ENTER key
  10. Use arrow keys to choose the correct satellite for your area. For a list of satellite frequencies, click here.
  11. Press ENTER key
  12. Press DOWN ARROW key until SATELLITE FREQ screen appears.
  13. This will list the frequency of the DGPS satellite you specified in the EZ SAT: field. Press DOWN ARROW key until SATELLITE BAUD RATE screen appears.
  14. This should update to the Data Rate of the satellite you specified in the EZ SAT: field. Press DOWN ARROW key until prompted to exit DGPS CONFIG. screen.
  15. Press ENTER key to exit.
  16. Allow 30-45 minutes to get the system to work during the activation process

OmniSTAR must then send an activation code (RSOC-type) over the satellite to the unit. When received, it will display RESET BY OMNI ACTIVATION, PLEASE HIT ENTER TO CONTINUE. It can take up to 30 minutes for activation to be complete. It is important that the system be left on until the receiver positions differentially.

To check that activation was successful:

  1. From the HOME SCREEN press the RIGHT ARROW key until you access the STATUS screen.
  2. Press DOWN ARROW key to enter these screens
  3. Use RIGHT ARROW key, access the DGPS SCREEN
  4. Press DOWN ARROW key.
  5. First screen should display Satellite Frequency and S/N of the satellite signal-noise ratio and the strength of the differential satellite lock.
  6. Press DOWN ARROW key and screen should display Omni as SERVICE PROVIDER.
  7. Press DOWN ARROW key and DGPS DATA SOURCE should read correct REFERENCE STATION ID.
  8. Press DOWN ARROW key and screen should display AGE of DGPS and AGE of SYNC.
  9. Press DOWN ARROW key until Omni*SERVICE INFO appears
  10. Press ENTER key to access this screen.
  11. Use ENTER key to scroll through the screens for status of the OmniStar subscription activation noting USER ENABLED and STOP DATE.
  12. Use ARROW keys to display HOME SCREEN.
  13. The HOME SCREEN will display on the top line, the type of position recorded. THE letter G will be replaced as a D when the receiver starts computing differentially corrected positions. The second line should display the DGPS satellite frequency.

To change to a satellite frequency that already exists in the EZ SAT list, follow the instructions above for Activation Set-up.

To change to a new satellite frequency that may not be in the EZ SAT list, follow the instructions below:

  1. From the HOME SCREEN press the RIGHT ARROW key until you access the CONFIGURATION screen.
  2. Press DOWN ARROW key to enter these screens
  3. Press RIGHT ARROW key until you access the DGPS CONFIGURATION screen.
  4. Press DOWN ARROW key until DGPS SOURCE screen appears.
  5. Press RIGHT ARROW key
  6. Press DOWN ARROW key until it says SATELLITE ONLY
  7. Press ENTER key
  8. Press DOWN ARROW key until SATELLITE FREQ screen appears.
  9. Press RIGHT ARROW key
  10. Use UP ARROW and DOWN ARROW keys to change the digits to the correct frequency for your area. Use the RIGHT ARROW key to move the cursor. For a list of satellite frequencies, click here.
  11. Press ENTER key
  12. Press DOWN ARROW key until SATELLITE BAUD screen appears.
  13. Press RIGHT ARROW key
  14. Use UP ARROW and DOWN ARROW keys to select the correct baud rate for your area. For a list of satellite frequencies and baud rates, click here.
  15. Press ENTER key to exit.
  16. Allow 30-45 minutes to get the system to work

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

Trimble AgGPS 132
Also:
OmniLite 132
OmniSTAR 3200

  RSOCVBS n/a  3.00 or 1.52 special
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
Trimble AgGPS 132
Also:
Trimble DSM132
P/N 33302-x0

 1.55  1.54  n/a  June 2007
VBS

Documentation available for the Trimble AgGPS 132 includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 DSM 232

  1. From the HOME SCREEN press the RIGHT ARROW key until you access the CONFIGURATION screen.
  2. Press DOWN ARROW key to enter these screens
  3. Press RIGHT ARROW key until you access the DGPS CONFIGURATION screen.
  4. Press DOWN ARROW key until DGPS SOURCE screen appears.
  5. Choose SATELLITE ONLY
  6. Press ENTER key
  7. Press DOWN ARROW key until EZ SAT: screen appears.
  8. Use arrow keys to set provider to OMNI
  9. Press ENTER key
  10. Use arrow keys to choose the correct satellite for your area. For a list of satellite frequencies, click here.
  11. Press ENTER key
  12. Press DOWN ARROW key until SATELLITE FREQ screen appears.
  13. This will list the frequency of the DGPS satellite you specified in the EZ SAT: field. Press DOWN ARROW key until SATELLITE BAUD RATE screen appears.
  14. This should update to the Data Rate of the satellite you specified in the EZ SAT: field. Press DOWN ARROW key until prompted to exit DGPS CONFIG. screen.
  15. Press ENTER key to exit.
  16. Allow 30-45 minutes to get the system to work during the activation process

OmniSTAR must then send an activation code (RSOC-type) over the satellite to the unit. When received, it will display RESET BY OMNI ACTIVATION, PLEASE HIT ENTER TO CONTINUE. It can take up to 30 minutes for activation to be complete. It is important that the system be left on until the receiver positions differentially.

To check that activation was successful:

  1. From the HOME SCREEN press the RIGHT ARROW key until you access the STATUS screen.
  2. Press DOWN ARROW key to enter these screens
  3. Use RIGHT ARROW key, access the DGPS SCREEN
  4. Press DOWN ARROW key.
  5. First screen should display Satellite Frequency and S/N of the satellite signal-noise ratio and the strength of the differential satellite lock.
  6. Press DOWN ARROW key and screen should display Omni as SERVICE PROVIDER.
  7. Press DOWN ARROW key and DGPS DATA SOURCE should read correct REFERENCE STATION ID.
  8. Press DOWN ARROW key and screen should display AGE of DGPS and AGE of SYNC.
  9. Press DOWN ARROW key until Omni*SERVICE INFO appears
  10. Press ENTER key to access this screen.
  11. Use ENTER key to scroll through the screens for status of the OmniStar subscription activation noting USER ENABLED and STOP DATE.
  12. Use ARROW keys to display HOME SCREEN.
  13. The HOME SCREEN will display on the top line, the type of position recorded. THE letter G will be replaced as a D when the receiver starts computing differentially corrected positions. The second line should display the DGPS satellite frequency.

To change to a satellite frequency that already exists in the EZ SAT list, follow the instructions above for Activation Set-up.

To change to a new satellite frequency that may not be in the EZ SAT list, follow the instructions below:

  1. From the HOME SCREEN press the RIGHT ARROW key until you access the CONFIGURATION screen.
  2. Press DOWN ARROW key to enter these screens
  3. Press RIGHT ARROW key until you access the DGPS CONFIGURATION screen.
  4. Press DOWN ARROW key until DGPS SOURCE screen appears.
  5. Press RIGHT ARROW key
  6. Press DOWN ARROW key until it says SATELLITE ONLY
  7. Press ENTER key
  8. Press DOWN ARROW key until SATELLITE FREQ screen appears.
  9. Press RIGHT ARROW key
  10. Use UP ARROW and DOWN ARROW keys to change the digits to the correct frequency for your area. Use the RIGHT ARROW key to move the cursor. For a list of satellite frequencies, click here.
  11. Press ENTER key
  12. Press DOWN ARROW key until SATELLITE BAUD screen appears.
  13. Press RIGHT ARROW key
  14. Use UP ARROW and DOWN ARROW keys to select the correct baud rate for your area. For a list of satellite frequencies and baud rates, click here.
  15. Press ENTER key to exit.
  16. Allow 30-45 minutes to get the system to work

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

Trimble AgGPS 332
Also:
Trimble DSM232

  RSOCVBS RSOCHP  3.1 / 3.5
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
Trimble AgGPS 332
Also:
Trimble DSM232

 3.70  3.1 3.1  Jan. 2006
VBS/HP
  • Download firmware from the manufacturer’s support website.
  • Download software tools from the manufacturer’s support website.
  • OmniSTAR technical note: To identify the firmware version, please refer to the manufacturer’s support website.

Documentation available for the Trimble AgGPS 332 from the manufacturer’s support website.

 EZ-Guide 500 System

For activation set-up, please refer to the manufacturer’s website at http://www.trimble.com/agriculture.

To change to a new satellite frequency, please refer to the manufacturer’s website at http://www.trimble.com/agriculture.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

Trimble EZ-Guide 500 System

  RSOCVBS RSOCHP  5.10
   GPS Receiver Model   
Latest   Firmware
 VBS2
 Compatible 
XP
 Compatible 
Release date 
  VBS/HP/G2 
Trimble EZ-Guide 500 System
5.10 All All  June 2007
VBS/HP

Documentation available for the Trimble EZ-Guide 500 System includes the following:

 FmX Integrated Display

For activation set-up, please refer to the manufacturer’s website at http://www.trimble.com/agriculture.

To change to a new satellite frequency, please refer to the manufacturer’s website at http://www.trimble.com/agriculture.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

Trimble FmX Integrated Display

  RSOCVBS RSOCHP TBA
   GPS Receiver Model   
Latest   Firmware
 VBS2
 Compatible 
XP
 Compatible 
Release date 
  VBS/HP/G2 

Trimble FmX Integrated Display

TBA All All TBA VBS/HP/G2

Documentation available for the Trimble FmX Integrated Display includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 Pathfinder Power

The first important thing is that you have a Trimble receiver with the latest firmware version. Please call your Trimble dealer or OmniSTAR for the latest update. Some subscription possibilities will not work with old firmware! Setup your Trimble receiver and switch it on. Make sure the receiver has a lock on the OmniSTAR satellite.

Important things OmniSTAR needs to know before they can subscribe:

  1. Type of receiver
  2. Serial number
  3. Type of activation you require
  4. Location
  5. Firmware of receiver
  6. Satellite service which the unit is locked onto.

For additional information, please refer to the manufacturer’s website at www.trimble.com.

Connect the serial cable to the Port on the receiver not used by your guidance system. Connect receiver to PC and run AgRemote software:

  1. Press the ESCAPE button until the “Home” screen appears.
  2. Press “>” RIGHT button until the “Configuration” screen appears.
  3. Press the “V” DOWN button once, a screen similar to below appears.
  4. Press the > RIGHT button until the “DGPS Config” screen.
  5. Press the V DOWN button until the “Satellite Freq” appears.
  6. Press the > RIGHT button for the cursor to flash on the first digit.
  7. Press the V DOWN and UP buttons to change the digits. Press the > RIGHT button to move on to the next digit until the desired frequency is displayed eg. 1535.1850 MHz.
  8. Press the ENTER button to lock in the new frequency. The cursor will disappear from the screen.

To check that your Pathfinder Power activation was successful:

  1. Press the ESC button until the “Home” screen appears.
  2. After changing the frequency, restore the settings of Port A to Port output NMEA baud rate 9600, 8, N, 1.
  3. The program will reply an error message: “Lost communications with the receiver check cables”.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

Pathfinder Power
  RSOCVBS n/a  
3.00
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 

Pathfinder Power

3.00

1.96

n/a

Aug 2007

VBS

Documentation available for the Trimble Pathfinder Power includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 Pathfinder ProXRS

  1. Access the “DGPS CONFIG” screen.
  2. Press ENTER button.
  3. Press DOWN ARROW button until “DGPS SOURCE” screen appears.
  4. Choose “SATELLITE ONLY”
  5. Press ENTER button.
  6. Press DOWN ARROW button until “EZ SAT:” screen appears.
  7. Use arrow keys to set provider to “OMNI”.
  8. Press ENTER button.
  9. Use arrow keys to choose the correct satellite for your area.
  10. Press ENTER button.
  11. Press DOWN ARROW button until “SATELLITE FREQ” screen appears.
  12. This will list the frequency of the DGPS satellite you specified in the EZ SAT: Field
  13. Press DOWN ARROW button until “SATELLITE BAUD RATE” screen appears.
  14. This should update to the Data Rate of the satellite you specified in the EZ SAT: Field
  15. Press DOWN ARROW button until prompted to exit “DGPS CONFIG” or “Exit Menu” screen.
  16. Press ENTER” button to exit.

OmniSTAR must then send an activation code over the satellite to the receiver. When received, it will display “RESET BY OMNI ACTIVATION”, please hit ENTER button to continue. It can take up to 30 minutes for activation to be complete. It is important that the system is switched on until the receiver positions differentially.

To check your ProXRS if the activation was successful:

  1. Use RIGHT ARROW button, access the “DGPS SCREEN”.
  2. Press DOWN ARROW button.
  3. First screen should display Satellite Frequency and S/N of the satellite signal-noise ratio and the strength of the differential satellite lock.
  4. Press DOWN ARROW button and screen should display Omni as “SERVICE PROVIDER”.
  5. Press DOWN ARROW button and “DGPS DATA SOURCE” should read the correct “REFERENCE STATION ID”.
  6. Press DOWN ARROW button and screen should display AGE of DGPS and AGE of SYNC.
  7. Press DOWN ARROW button until “OMNI*SERVICE INFO” appears.
  8. Press ENTER button to access this screen.
  9. Press ENTER button to scroll through the screens for status of the OmniSTAR subscription activation noting “USER ENABLED” and next screen “STOP DATE”, and some more information about Omnistar.
  10. Use both ARROW buttons to display HOME SCEEN (press both arrow buttons three times at the same time).

The HOME SCREEN will display on the top line, the type of position recorded. The letter G will be replaced as a D when the receiver starts computing differentially corrected positions. The second line should display the DGPS satellite frequency. This may take up to 30 minutes to indicate receiver is in differential mode even though the OmniSTAR activation shows enabled.

  1. Connect the computer to Port B and run AgRemote.
  2. Press the ESCAPE button until the “Home” screen appears.
  3. Press RIGHT ARROW button until the “Configuration” screen appears.
  4. Press the DOWN ARROW button once.
  5. Press the RIGHT ARROW button until the “DGPS Config” screen.
  6. Press the DOWN ARROW button until the “Satellite Freq” appears.
  7. Press the RIGHT ARROW button for the cursor to flash on the first digit.
  8. Press the DOWN and UP ARROW buttons to change the digits.
  9. Press the RIGHT ARROW button to move on to the next digit until the desired frequency is displayed eg. 1535.1850 MHz.
  10. Press the ENTER button to lock in the new frequency. The cursor will disappear from the screen.
  11. CHECK THE FREQUENCY ON YOUR RECEIVER IS ENTERED IN CORRECTLY.
  12. Press the ESC button until the “Home” screen appears.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 
Pathfinder ProXRS
  RSOCVBS n/a  1.52
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
Pathfinder ProXRS





 p/n 33302-51, 33302-53 1.96
1.96
 n/a Aug. 2007
 VBS
 p/n 33302-50
 1.55 1.54
 n/a June 2007
 VBS

Documentation available for the Trimble Pathfinder ProXRS includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 Pathfinder ProXRT

The first important thing is that you have a Trimble receiver with the latest firmware version. Please call your Trimble dealer or OmniSTAR for the latest update. Some subscription possibilities will not work with old firmware! Setup your Trimble receiver and switch it on. Make sure the receiver has a lock on the OmniSTAR satellite.

Important things OmniSTAR needs to know before they can subscribe:

  1. Type of receiver
  2. Serial number
  3. Type of activation you require
  4. Location
  5. Firmware of receiver
  6. Satellite service which the unit is locked onto.

For additional information, please refer to the manufacturer’s website at www.trimble.com.

For more information, please refer to the manufacturer’s website at http://www.trimble.com/.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 
ProXRT RSOCVBS RSOCHP 4.15
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
ProXRT 4.15 3.60 n/a October 2010 VBS/HP/G2

Documentation available for the Trimble ProXRT includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 R7

For activation setup, please refer to the manufacturer’s website at www.trimble.com.

For changing to a new satellite frequency, please refer to the manufacturer’s website at www.trimble.com.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

 
Trimble R7

RSOCVBS RSOCHP TBA
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
Trimble R7 TBA
TBA

TBA VBS/HP/G2

Documentation available for the Trimble R7 includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 SPS-461 / SPS-361

For activation set-up, please refer to the manufacturer’s website at www.trimble.com.

To change to a new satellite frequency, please refer to the manufacturer’s website at www.trimble.com.

For the minimum receiver firmware requirements for OmniSTAR service, please refer to the manufacturer’s website at www.trimble.com.

For the latest receiver firmware versions and upgrades, please refer to the manufacturer’s website at www.trimble.com.

Documentation available for the Trimble SPS-461 and SPS-361 from the manufacturer’s support website.

 SPS-550 Series

For activation set-up, please refer to the manufacturer’s website at www.trimble.com.

To change to a new satellite frequency, please refer to the manufacturer’s website at www.trimble.com.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 
Trimble SPS-550 series RSOCVBS RSOCHP 4.14
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
Trimble SPS-550 series 4.14 3.00 3.00 June 2006 VBS/HP

Documentation available for the Trimble SPS-550 series includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 SPS-750 Series

For activation set-up, please refer to the manufacturer’s website at www.trimble.com.

To change to a new satellite frequency, please refer to the manufacturer’s website at www.trimble.com.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 
Trimble SPS-750 series RSOCVBS RSOCHP 4.14
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
Trimble SPS-750 series 4.14 3.00 3.00 June 2006 VBS/HP

Documentation available for the Trimble SPS-750 series includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 SPS-850 Series

For activation set-up, please refer to the manufacturer’s website at www.trimble.com.

To change to a new satellite frequency, please refer to the manufacturer’s website at www.trimble.com.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

 
Trimble SPS-850 Series

RSOCVBS RSOCHP 4.14
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
Trimble SPS-850 Series 4.14 3.00 n/a June 2006 VBS/HP

Documentation available for the Trimble SPS-850 Series includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 SPS-855

For activation set-up, please refer to the manufacturer’s website at www.trimble.com.

To change to a new satellite frequency, please refer to the manufacturer’s website at www.trimble.com.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

 
Trimble SPS-855

RSOCVBS RSOCHP 4.61
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
Trimble SPS-855 4.61 4.61
Yes
May 2012 VBS/HP/G2

Documentation available for the Trimble SPS-855 includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.

 SPS-985

For activation set-up, please refer to the manufacturer’s website at www.trimble.com.

To change to a new satellite frequency, please refer to the manufacturer’s website at www.trimble.com.

Below are the minimum receiver firmware requirements for OmniSTAR service. To download the latest firmware, check the Latest Firmware Versions information below or visit Trimble’s support website.

   GPS Receiver Model   
  VBS Subscription  
  HP/XP Subscription  
   Firmware Version 

 
Trimble SPS-985

RSOCVBS RSOCHP 4.61
   GPS Receiver Model   
 Latest
  Firmware 
 VBS2
 Compatible 
XP
  Compatible 
   Release date 
  VBS/HP/G2 
Trimble SPS-985 4.61 4.61
Yes
May 2012 VBS/HP/G2

Documentation available for the Trimble SPS-985 includes the following:

For additional information, please refer to the manufacturer’s website at www.trimble.com.